- 您现在的位置：买卖IC网 > Sheet目录221 > DMS-20LCD-4/20S-C (Murata Power Solutions Inc)METER LCD SELF-POWERED 3.5DIG
DMS-20LCD-4/20 Series
4-20mA Input Loop-Powered Ultra-Low 1.8V Loop Drop
3? Digit LCD Display Process Monitors
The ?rst step when con?guring the DMS-20LCD-4/20P for the ?rst time, or
Examples (DMS-20LCD-4/20P-Positive Model)
when selecting a new range, is to set R3 fully counterclockwise and R7 fully
clockwise (roughly 22 turns) to their minimum offset/minimum span posi-
tions, respectively.
1. Desired display readings are:
4mA = “650”
ON
The next step is to calculate the required display differential-reading; this
20mA = “950”
1
2
3
4
5
6
is accomplished by subtracting the desired 4mA display reading from the
desired 20mA display reading, disregarding decimal points. Then, using the
calculated differential display-reading to select the appropriate DIP-switch
setting # from Table 3, con?gure DIP-switches SW1, SW2, and SW3 accord-
ingly. Make certain that the DIP-switch’s small actuators are ?rmly engaged
Use DIP-switch setting #4 in Table 3 since subtracting 650 from 950 yields
a differential value of 300. Apply 4mA and adjust R3 until the display reads
“000”. Apply 20mA and adjust R7 until the display reads “300” (the differen-
tial value previously calculated). Apply 4mA and adjust R3 until the display
reads “650”. Apply 20mA and verify that the display reads “950”.
in their fully-ON or fully-OFF positions.
2. Desired display readings are:
ON
The procedure below describes how to calibrate the meter for an application
which the DMS-20LCD-4/20P easily accommodates: displaying the output
of a 4-20mA transmitter, that is, "04.0" with a 4mA input and "20.0" with a
4mA = “4.00”
20mA = “19.99”
1
2
3
4
5
6
20mA input.
1. Set R3 fully counterclockwise (minimum offset position) and R7 fully
clockwise (minimum differential span position), roughly 22 turns.
2. Subtract 040 from 200 to yield a differential value of 160; use
this value to select DIP-switch setting #5 in Table 3. Enable decimal
point DP3 by placing SW6 to the ON position.
3. Set the transmitter’s output to 4.0mA and carefully adjust R3 clockwise
until the meter’s display reads “000”.
4. Set the transmitter’s output to 20.0mA and adjust R7 counterclock-
wise until the meter’s display reads “16.0”.
5. Set the transmitter back to 4.0mA and slowly adjust R3 clockwise until
the display reads “04.0”. Reapply 20.0mA and the display should now
read “20.0”. Repeat steps 3, 4 and 5 to make sure the adjustments did
This example illustrates the DMS-20LCD-4/20P’s capability to display higher
differential readings than those indicated in Table 3. This example also
illustrates how the DMS-20LCD-4/20P can be used to display the output
levels of a 4-20mA loop transmitter with higher precision (0.01mA versus
0.1mA) than described above.
Subtracting 400 from 1999 yields a differential of 1599, a value not listed in
Table 3. However, use DIP-switch setting #1 in Table 3 since this setting has
the highest overall offset/span adjustment capabilities. Enable DP2 via SW5
then apply 4mA and adjust R3 so the display reads “0.00”. Apply 20mA and
adjust R7 so the display reads “15.99”. Apply 4mA and adjust R3 until the
display reads “4.00”. Apply 20mA and check to see that the display reads
“19.99” or just overranges (“1—“). Repeat adjustment procedure if neces-
sary.
Table 4. Decimal Point Settings
not affect one another.
T able 3. DMS-20LCD-4/20P (Pos. Reading) DIP-Switch Settings ?
SW4
DP1
SW5
DP2
SW6
DP3
Display Reading
Differential Range
4mA Input
20mA Input
SW1
SW2
SW3
1 . 800-1400
2. 500-800
3. 350-500
4. 250-350
5. 150-250
900
850
800
750
750
1700
1350
1150
1000
900
Off
On
Off
Off
On
Off
Off
On
Off
On
Off
Off
Off
On
On
www.murata-ps.com/dpm
Technical enquiries email: sales@murata-ps.com, tel: +1 508 339 3000
MPM_DMS20LCD-420.B03 Page 4 of 6
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
DMS-20PC-0/5-5BS-C
MONITOR CTRL LED 0-5V 3.5DIG BLU
DMS-20PC-0-DCM-B-C
DPM LED 4.5-19.99V 3.5DIGIT BLUE
DMS-20PC-1-LM-G-C
DPM LED 85-264VAC 3DIGIT GREEN
DMS-20PC-1-PGL-C
DPM LED 2V 3.5DIGIT LO-PWR GRN
DMS-20PC-2-LM-C
DPM LED 240-310VAC 3DIGIT RED
DMS-20PC-3-DCM-C
DPM LED SELF-POWERED 2-11VDC RED
DMS-20PC-3-FM-C
METER FREQ LED 220V 47-99HZ RED
DMS-20PC-3-LM-C
DPM LED 350-600VAC 3DIGIT RED
相关代理商/技术参数
DMS20N
制造商:Rochester Electronics LLC 功能描述:- Bulk
DMS-20PC
制造商:未知厂家 制造商全称:未知厂家 功能描述:3 Digit, LED Display Low-Cost, Subminiature Digital Panel Voltmeters
DMS-20PC-0
制造商:未知厂家 制造商全称:未知厂家 功能描述:3 Digit, LED Display Low-Cost, Subminiature Digital Panel Voltmeters
DMS-20PC-0/5-24RL
功能描述:数字面板表 0-5V and 0-10V input 3 1/2 digit red LED RoHS:否 制造商:Murata Power Solutions 设备类型:AC Voltmeters 显示器类型:LED, 3 Digit, Red 工作电源电压:85 VAC to 264 VAC 工作电源电流:50 mArms 输入电流:50 mA 输入频率: 输入电压:120 VAC 系列:DMS-20PC-1-LM
DMS-20PC-0/5-24RL-C
功能描述:数字面板表 0-5V and 0-10V input RoHS:否 制造商:Murata Power Solutions 设备类型:AC Voltmeters 显示器类型:LED, 3 Digit, Red 工作电源电压:85 VAC to 264 VAC 工作电源电流:50 mArms 输入电流:50 mA 输入频率: 输入电压:120 VAC 系列:DMS-20PC-1-LM
DMS-20PC-0/5-5BS
功能描述:数字面板表 0-5V 3 1/2 Digit LED Bright Blue RoHS:否 制造商:Murata Power Solutions 设备类型:AC Voltmeters 显示器类型:LED, 3 Digit, Red 工作电源电压:85 VAC to 264 VAC 工作电源电流:50 mArms 输入电流:50 mA 输入频率: 输入电压:120 VAC 系列:DMS-20PC-1-LM
DMS-20PC-0/5-5BS-C
功能描述:数字面板表 0-5V 3 1/2 Digit LED Bright Blue RoHS:否 制造商:Murata Power Solutions 设备类型:AC Voltmeters 显示器类型:LED, 3 Digit, Red 工作电源电压:85 VAC to 264 VAC 工作电源电流:50 mArms 输入电流:50 mA 输入频率: 输入电压:120 VAC 系列:DMS-20PC-1-LM
DMS-20PC-0/5-5GS
功能描述:数字面板表 0-5V 3 1/2 Digit LED Std Intense Green RoHS:否 制造商:Murata Power Solutions 设备类型:AC Voltmeters 显示器类型:LED, 3 Digit, Red 工作电源电压:85 VAC to 264 VAC 工作电源电流:50 mArms 输入电流:50 mA 输入频率: 输入电压:120 VAC 系列:DMS-20PC-1-LM